<img height="1" width="1" style="display:none" src="https://www.facebook.com/tr?id=1269321669886585&amp;ev=PageView&amp;noscript=1">

Inside Frequency Control

Inside an OCXO – Key Performance Abilities

Posted by Rob Rutkowski on Mar 16, 2017 6:25:00 AM

OCXO Performance.jpg

When High Stability is a Must

Oven Controlled crystal (Xtal) Oscillators, OCXOs, are used in applications where a very high degree of frequency stability is required. Sometimes these oscillators may even be referred to as temperature stabilized crystal oscillators, or just crystal ovens.

While crystal oscillators (3 main types) show a high degree of stability even when the outside temperature is varied over a significant range, for some applications even higher levels of temperature stability are required. In these applications, OCXOs may provide the required solution.

As with many other crystal based products, OCXOs are available in a widely variation of packages and package styles. The performance levels and costs also need to be considered as these can vary considerably as well.

 

The OCXO Super Power - The Ability to Control Temperature

It is still sometimes necessary to ensure an even better degree of stability. This can be achieved by placing the crystal in a thermally insulated container with a thermostatically controlled heater. By heating the crystal to a temperature above that which would normally be encountered within the electronic equipment, the temperature of the crystal can be maintained at a constant temperature. This results in a far greater degree of temperature stability. Additionally, the crystal in the OCXO will be cut to ensure that its temperature stability is optimized for the internal operating temperature.

Consider learning more about The Different Types of Crystals in your Oscillators

Commonly the internal temperature for a crystal oven is run at a temperature of 75°C or thereabouts. The temperature needs to be above the highest temperature likely to be encountered, otherwise the temperature control will not work.

The typical specification for an OCXO might be ±5 x 10-8 per degree Celsius (0.05 ppm), whereas a non-oven controlled oscillator may be between 10 and 100 times poorer. As the oscillator assembly will also contain buffering circuitry as well as supply voltage regulation the other characteristics of the oscillator should also be good. Typically, it might be expected that frequency stability would be around ±5 x 10-9 (0.005 ppm) per day and ±5 x 10-7 (0.5 ppm) per year and 1 x 10-7 for a 5% change in supply voltage. These are far better than would be expected from a simple crystal oscillator.

To ensure that the optimum overall accuracy is maintained, combating elements such as ageing of the crystal itself and a periodic calibration of the OCXO may be required. Typical calibration periods may be of the order of six months to a year, but the actual period will depend upon the OCXO itself and the requirements of the application in which it is being used.

 

Physical Qualities of an OCXO

OCXOs are physically much larger than a simple crystal oscillator. This is because they:

  1. Incorporate the crystal oscillator itself
  2. Contain a heater
  3. Contain control circuitry
  4. House thermal insulation around the crystal oscillator

Typically, the heater will be run from a different supply to the oscillator. It does not need the same level of regulation. Indeed, the oscillator is most likely to have its own regulator to remove any stray noise and RF that may appear on the supply line. This will therefore degrade the performance of the OCXO.

The supply for the heater in the OCXO may be quite current hungry. Some units may require an Amp or so on warm up. This figure will reduce as the temperature inside the OCXO rises and less heat is needed. As will be imagined the temperature is thermostatically controlled.

 

These OCXO units are naturally more expensive than crystals on their own, but the performance of an OCXO is considerably enhanced on that of a simple crystal in an unregulated electrical and physical environment.

 

How About Some More Specifics?

Wow! So much to consider and worry about when designing and selecting crystal oscillators. However, this is only the beginning. Check out the post Anatomy of an OCXO to learn how these qualities and abilities you just learned specifically affect an OCXO’s performance in your applications.  Yay for more details! (Especially for you more advanced engineers).

Topics: engineering, crystal oscillators, RF Technology